Twfta Marketplace
Products Companies Find Suppliers Find buyer
 
Mud Pump, F-1000, F-800,F-500,F-1300,F-1600,PZ-9,12-P-160 Mud pumps,Fluid End Parts, Piston, Liners, Valves ,seats, Modules, Rod and Clamps. Casing slips, Rotary slips, Drill collar slips  

 
  Company Profile
  Products Showroom
  Contact Us
 




 

Mud Pump F-1000




        Inquiry   Now      
        Contact   Info       
   
   


F-1000 single acting triplex mud pumps are authorized by Continental Emsco Company to manufacture in China and fully conform to Continental Emsco Company"s technical requirement.

F-1000 mud pumps are rated at longer stroke length and relatively low stroke per minute. It can increase the service life of expendable parts of fluid end assembly.

The fluid end assembly mainly consists of fluid end, valve assembly, liners and pistons. Fluid end is made of forged alloy steel and three fluid ends of each pump are interchangeable. The suction valve and discharge valve of F mud pump are interchangeable. Liners use Bi metal, the sleeve is made of wear resisting cast iron. Piston and piton rod are of slide fit and sealed with rubber seal rings and are fastened with lock nuts to prevent the piston from loosing.

The valve seat bores have bottom shoulders. The piston and liners are spray lubricated and cooled which allow an extended service life.

The power end assembly mainly consists of frame, crankshaft, pinion shaft, crosshead and extension rod.

Continuous tooth herringbone gear.
One-piece alloy steel crankshaft.
Replaceable crosshead guides.
Frame fabricated steel plate weldment provides the optimum rigidity, high strength and lightweight.
Double sealing structure for extension rod provides good sealing.

Power end utilizes the combination lubricating system of forced lubrication and splashing lubrication.




Jinan Oilfield Equipment Enterprise Products

Mud Pump F-1000
F-1000 single acting triplex mud pumps are authorized by Continental Emsco Company to manufacture in China and fully conform to Continental Emsco Company"s technical requirement. F-1000 mud pumps are rated at longer stroke length and relatively low stroke per minute. It can increase the...,Mud Pump F-1000 , Mud Pump F-1000
 
Mud pump Fluid End --- Liners
Mud Pump Fluid End Parts Liners Hardened liners; OEE hardened liners offer economy in a liner that is made for normal to mildly corrosive mud conditions. These liners are hardened and heat treated under strict quality control to a minimum of 60 RC hardness and a depth of. 125 inches. Each...,Mud pump Fluid End --- Liners , Mud pump Fluid End, Liners
 
Wellhead Tools,Rotary Slip,Casing Slips,Type Flake Rotary Slip,Drill Collar Slip, Safety Clamp,
Wellhead Tools Rotary Slip: Rotary Slip is suitable for the Pipe that diameter ranges between 2 3/8"and 5 1/2" (60.3mm-139.7mm). According to the contact length between Slip Insert and Pipe, Rotary Slips are three types available, SDS(Short Rotary Slips), SDML(Medium Rotary...,Wellhead Tools,Rotary Slip,Casing Slips,Type Flake Rotary Slip,Drill Collar Slip, Safety Clamp, , Wellhead Tools,Rotary Slip,Casing Slips,Type Flake Rotary Slip,Drill Collar Slip, Safety Clamp,
 
Mud Pump F-1300 F-1600
We are a large mud pump and Fluid End Expendables manufacturer in China. We speciaize in the development and manufacture the drilling tools, petroleum equipment, mud pump and the fluid end expendables. We have the F-500, F-650, F-800, F-1000, F-1300, F-1600 and PZ-9 mud pumps in strore. The...,Mud Pump F-1300 F-1600 , Mud Pump F-1300 F-1600
 
 
Contact Info
URL:
TEL:
Fax:
Country: China
Address:
Room 221, Yijing Building, Jinan China

Send Inquiry

 
Company:
*Contact:
*Email:
URL:
TEL:
Fax:
Country:
Address:
*Subject:
Comment:
 

 
 
 
  Contact Us Site Map About Us Trade Links
2005-2014 copyright by twfta.com. All rights reserved.